2024 STATE TECHNICAL STANDARDS • PAGE 15 Online Online Resumé Resumé Submission Submission SERIES: BUILDING TRADES B CONTEST: CABINETMAKING CONTEST: CABINETMAKING Series Director: RAY MAHON • (508) 769-5728 • [email protected] Competition: Tri-County - Carpentry Rooms with Event Manager: Christopher Ward REQUIREMENTS AND SCOPE OF CONTEST Advisors will be sent log-on information for the Learning Management System Learning Management System, which will be open on April 10. Contestants must submit an electronic copy of their resumé to the LMS LMS by April 22, by 5:00pm. Contestants must submit an electronic copy of the Cabinetmaking Memorandum to the LMS LMS by April 22, by 5:00pm. Clothing Requirements: avoid a clothing penalty Khaki work pants, as shown Leather work boots Safety glasses MUST BE WORN AT ALL TIMES MUST BE WORN AT ALL TIMES SkillsUSA Massachusetts T-Shirt, provided Hard Hat, not required NO cell phones or SmartWatches allowed Safety: avoid a safety violation or being removed from the contest NO loose/long hair (must be secured) NO loose clothing NO jewelry No sneakers Tool Requirements: Contestants must submit online a one-page type-written resume, failure to do so will result in a 50-point penalty Contestant’s Cabinetmaking Memorandum must be completed, signed and submitted to the LMS by April 26, see page 16 for form and details Contestant’s Cabinetmaking Memorandum must be completed, signed and submitted to the LMS by April 26, see page 16 for form and details Tape measure or rule Utility knife with blades Protractor Dovetail saw Back saw Combination square Set of dividers or compass Coping saw with extra blade Hammer Plastic mallet Sliding T bevel #1, #2, #3 Phillips screwdrivers 2 - pencils, sharpened 3/16, 1/4 slotted screwdrivers Drill index 1/16 to 3/8 x 1/16 1/4” collet router Biscuit jointer 1 pt. Wood glue 1 qt. Nontoxic contact cement 2 – contact cement application brushes Nail Set 6” machinist scale Phillips screwdriver bit set for drill Edge banding trimmer Power drill 3/8 or 1/2 (cordless or corded) and driver Laminate tools, flat mill file, plastic laminate roller, electric trimmer, flush cutter, bevel cutter Set of wood chisels (1/4”, 3/8”, 1/2”, 3/4”, 1”) (Chisels must be ground and sharpened) (Chisels must be ground and sharpened) National Skills: Contestants are required to build a small cabinet from materials and drawings supplied. They are expected to read the drawings, lay out and cut the parts, using a table saw, laminate trimmer, hand drill, hinge boring machine and various hand tools. The parts are to be accurately assembled, sanded and adjusted to tolerances as specified by the judges. State Skills: The event will include 10-12 of the following: 1. Mortise in a butt hinge 2. Layout and band saw a valance 3. Blind dado 4. Spline joint 5. Spline flat miter joint 6. Haunched mortise and tenon 7. Drawer Corner joint (DBL DADO) 8. Pocket hole 9. Pocket hole dado 10. Cope joint 11. Flat miter and doweled 12. Turn a round tapered leg 13. Drawer Front dovetail 14. Machine dovetail 15. Plastic laminating 16. Square tapered leg jig and leg (4 sides) 17. Layout and cut a cabriole leg 18. Layout rod 19. Mortise and tenon table leg and rail 20. Bridle joint 21. Set up a knife and collar on the shaper 22. Turn a leg with beads, coves, and half rounds 23. Through dovetail 24. Biscuit joinery 25. Cabinet carcass assembly 26. Assemble & install doors 27. Layout and install door & draw hardware 28. Assemble & install drawers 29. Mechanical draw slides Online Online Submission Submission by April 26 by April 26
.png?v=1694020562592)
